1970s brick-and-cedar split-level house at dusk in early October, a sugar maple turning orange over the lawn and fallen leaves on the sidewalk

Furnace maintenance in Naperville, IL

The short answer

Furnace maintenance in Naperville, IL runs $119 for a 60–90 minute tune-up: a 21-point inspection covering the heat exchanger, burner and flame quality, combustion and carbon monoxide testing, and safety controls, with the findings written on the invoice. FortHouse Heating & Cooling also writes the blower motor amp draw on that invoice. Book it in early fall, in September or October, before the furnace runs every day. If it finds a worn blower motor, the City's own electric utility pays eligible customers $100 toward the replacement.

Written by the FortHouse Team. Tune-ups by EPA 608 and NATE-certified technicians.

Does your Naperville furnace need a tune-up this fall?

  • It skipped last year's service

    A dirty flame sensor and a clogged filter are two of the most common reasons for a no-heat call, and the visit deals with both.

  • It's a 95% furnace

    Its PVC vents and condensate drain need to be clear before the first freeze, when a blockage makes it shut itself off.

  • It's 10 years old or more

    The City of Naperville puts a blower motor's life at 10 to 15 years, and the amp-draw reading shows the wear before the motor quits.

  • You just bought the house

    You get a written set of baseline readings for a furnace someone else ran and maintained.

How much does furnace maintenance cost in Naperville, IL?

$119 covers all 21 points. Here are five of the checks, the reading each produces, and where a bad reading leads
CheckWhat gets measuredPriceIf the reading is off
Heat exchangerCracks, corrosion, rust-throughIncludedA crack ends the repair question. We show it to you and price a replacement.
Combustion and carbon monoxideAnalyzer readings at the furnaceIncludedOut-of-range numbers are traced to a cause, usually the burner or venting, and priced in writing.
Blower motor amp drawCurrent against the motor's ratingIncludedA high reading means a wearing motor: $450–$2,500 to replace, with $100 back from the City for eligible customers.
Flame sensor and ignitorIgnition and flame signalIncludedThe sensor is cleaned during the visit. A weak ignitor is a $200–$400 part, quoted before it's changed.
Venting and drainFlue draft, or PVC and condensate on a 95%IncludedA blocked drain or vent shuts a condensing furnace down, so it's cleared or quoted before you leave the basement.

All 21 points sit inside the $119, so the bill doesn't grow as the technician works down the list. These five each leave a number you can compare next fall. Keep the invoice: a climbing amp draw or a drifting combustion reading shows a part wearing out before it fails.

The tune-up flagged the blower motor. New motor or new furnace?

Apply the usual two tests. Multiply the furnace's age by the quote: past $5,000, the money belongs in a new furnace. And no single repair should cost more than half of a replacement, which runs $5,000–$9,000 installed in Naperville. For a City electric customer, the $100 motor credit tips a close call slightly toward the repair.

Repair is likely right when

  • The furnace is under about 12 and its heat exchanger passed
  • Only the motor, or its $200–$400 capacitor, is failing
  • You're a City electric customer who can claim the $100 credit

Replacement usually wins when

  • The furnace is past 15 and this is its second major part
  • The same visit found cracks or rust-through on the heat exchanger
  • The motor quote tops half the price of a new furnace
Age × repair cost, worked examples
Furnace ageRepair quoteAge × costVerdict
6 years$450 motor2,700Replace the motor
11 years$450 motor4,950Close: price both
18 years$1,200 motor21,600Replace the furnace

How does a Naperville furnace tune-up go?

  1. Before the visit

    Book in September or October

    Online or by phone, before the heat runs every day. Make the furnace's model sticker easy to reach: it tells us the age and the blower motor's rated amps.

  2. Arrival

    Power off, panels open

    The technician shuts the furnace off at its switch, takes the doors off, and checks the filter first, since a clogged one changes every reading after it.

  3. The visit

    21 points, measured

    Heat exchanger, burner and flame, ignitor and sensor, gas pressure, combustion and CO, safety switches, inducer, blower amp draw and temperature rise, in 60–90 minutes.

  4. A full heating cycle

    The furnace runs from the thermostat's call through ignition, heat and shutdown, so a fault that only appears mid-cycle doesn't slip past.

  5. Before we leave

    Readings, and a price if needed

    Every reading goes on the invoice. Anything failing gets a written price, and nothing is fixed until you say so.

What does the technician check up close?

New Carrier Infinity gas furnace and evaporator coil with wireless test probes attached at startup
Wireless probes reading a furnace at startup. A tune-up takes the same kind of readings and writes them down.
Carrier Infinity furnace with PVC vent and intake pipes and a gas line shutoff valve beside it
The PVC intake and exhaust a tune-up checks on a 95% furnace, beside the gas shutoff it tests for leaks.
Side view of a newly installed furnace with new sheet-metal supply plenum, return duct, and filter rack
The filter rack, the first stop on every visit, because the filter decides how hard the blower works.

What's particular to furnace maintenance in Naperville?

A City-owned electric utility

Inside Naperville, electricity comes from the City, not ComEd. The Department of Public Utilities–Electric serves more than 63,000 customers on a system that is 95% underground, and the City reports its customers averaged just 15 minutes without power in 2025. A gas furnace still can't run without it: the ignitor, inducer and blower are all electric. If the house goes dark, report it to the City's Customer Care Center at 630-420-6060, staffed around the clock, before booking a furnace visit.

$100 for a blower motor

The tune-up's blower amp-draw test matters more here, because the City pays toward what it can lead to. If the furnace blower motor gets replaced, a residential Naperville Electric Utility customer can claim a $100 incentive as a bill credit. The conditions: apply within 120 days, with the dated, paid invoice. It's one per household. New construction doesn't qualify. And you must give at least $5 a month to the City's Renewable Energy Program for five years after the award. The City says a blower motor lasts 10 to 15 years.

$75 for a smart thermostat

The same utility pays a $75 bill credit to residential customers, owners and renters alike, who buy and install a Wi-Fi smart thermostat costing at least $75. Each household can claim two, the application is due within 120 days of installation, and the City pays them until the funding runs out. The tune-up already tests how the furnace answers the thermostat's call for heat, so it's a sensible visit to add a smart thermostat to.

Questions Naperville homeowners ask

How much does furnace maintenance cost in Naperville, IL?

$119 for a full 21-point tune-up, with everything included: heat exchanger inspection, burner and flame quality, combustion and carbon monoxide testing, safety control verification and the blower motor amp draw, among others. It's the same price whether the furnace is an original in an older split-level or a newer high-efficiency unit. The visit takes 60–90 minutes, nothing on the checklist is added to the bill as it's found, and a repair only gets priced, in writing, when the readings call for one.

Does the City of Naperville pay anything back for furnace work?

Not for the tune-up itself, but for two things it can lead to. Residential customers of the Naperville Electric Utility can claim $100 after a furnace blower motor replacement, which requires a five-year, $5-a-month Renewable Energy Program contribution, and $75 for a smart thermostat. Both arrive as bill credits, both need the application within 120 days, and the City offers them as funding allows. Nicor Gas's rebates are separate and apply to new 95%+ furnaces.

Is a tune-up on a 95% furnace any different?

The 21 points are the same. On a condensing furnace, FortHouse Heating & Cooling's venting check covers the PVC intake and exhaust pipes and the condensate drain, since a blocked drain is a common reason a high-efficiency furnace shuts itself off on its first cold night. On an 80% furnace, the same check looks at the metal flue and its draft.

When is the best time for furnace maintenance in Naperville?

Early fall, in September or October, before the heat goes on. Once the nights turn cold, FortHouse Heating & Cooling's calendar fills with no-heat calls, and a tune-up booked then waits behind them. An early visit also leaves time to order a part, such as a blower motor, before the house depends on the furnace every day. Why the fall window matters goes deeper on the timing.

What happens if the tune-up finds a problem?

FortHouse Heating & Cooling shows you the reading and gives a written price before anything is repaired, and the decision stays yours. Typical finds: an ignitor at $200–$400, a blower capacitor at $200–$400, and a blower motor at $450–$2,500, each on top of the $119 visit. Furnace repair in Naperville lists the rest.

Is it the power or the furnace?

If the lights and outlets are dead too, it's the power, and Naperville's electric utility takes outage reports at 630-420-6060 at any hour. If the house has power and the furnace still won't start, check the furnace's own switch and breaker, then call FortHouse Heating & Cooling.

How long does a furnace tune-up take?

60–90 minutes for the full 21-point inspection, with the heat exchanger inspection taking the longest, especially on an older furnace near the Historic District. A visit much shorter than an hour usually means something got skipped.

Sources

The $119 price and the 21-point checklist are FortHouse's published tune-up terms. Incentive amounts, deadlines and conditions come from the City of Naperville's Electric Utility pages as of October 2026. The City pays them as funding allows, so confirm one is open before counting on it.

Book your Naperville furnace tune-up

After hours? Call (630) 318-6246, answered 24/7.

By submitting, you agree that FortHouse may contact you about this request. See our privacy policy.